|Home > What's New > Upper Saddle River, NJ - August 28, 2017|
Upper Saddle River, NJ - August 28, 2017 - Pentek, Inc., today introduced the newest member of the Jade" family of high-performance data converter XMC modules based on the Xilinx Kintex Ultrascale FPGA. The Model 71141 is a 6.4 GHz dual channel analog-to-digital and digital-to-analog converter with programmable DDCs and DUCs.
The Model 71141 is suitable for connection to IF or RF signals for very wideband communications or radar system applications including:
For applications that require unique functions, users can install custom IP for specialized data processing tasks. Pentek's Navigator" FPGA Design Kit includes source code for all factory-installed IP modules. Developers can integrate their own IP with the Pentek functions or use the Navigator kit to completely replace the Pentek IP with their own.
"The new Jade product family of high-performance processing boards utilize TI's LMX2594, ADC12DJ3200 and DAC38RF82 RF sampling data converters to boost wideband solution performance to a new level -- two times faster than previous generations of Pentek products," said VC Kumar, high-speed data converter manager at Texas Instruments. He added, "Designers can leverage this performance to move closer to the antenna, capture the wider bandwidths and process more information in real time."
"With direct radio frequency (RF) sampling of signals up to 8.1 GHz, the Model 71141 not only covers L-band, S-band and C-band, but also extends into X-band. Now RF designers can digitize large frequency spans with a single board solution," said Bob Sgandurra, director of Product Management
The Model 71141 is the first of the Pentek Jade products to use the Texas Instruments ADC12DJ3200 12-bit A/D. The front end accepts analog RF inputs on a pair of front panel SSMC connectors. The converter operates in single-channel interleaved mode with a sampling rate of 6.4 GHz and an input bandwidth of 7.9 GHz; or, in dual-channel mode with a sampling rate of 3.2 GHz and input bandwidth of 8.1 GHz.
The A/D built-in digital down converters support 2x decimation in real output mode and 4x, 8x or 16x decimation in complex output mode. The A/D digital outputs are delivered into the FPGA for signal processing, data capture or for routing to other module resources.
A Texas Instruments DAC38RF82 D/A with DUC accepts a baseband real or complex data stream from the FPGA and provides that input to the upconversion, interpolation and dual D/A stages. When operating as a DUC, it interpolates and translates real or complex baseband input signals. It delivers real or quadrature (I+Q) analog outputs to the dual 14-bit D/A converter. The two 6.4 GHz 14-bit D/As pair well with the dual input channels while delivering more than twice the output performance of previous generations of Pentek products.
The 71141 factory-installed functions include two A/D acquisition and two D/A waveform generation IP modules. In addition, IP modules for DDR4 SDRAM memories, a controller for all data clocking and synchronization functions, a test signal generator and a PCIe Gen.3 interface complete the factory-installed functions. System integrators get to market with less time and risk, because the 71141 delivers a complete turnkey solution without the need to develop any FPGA IP.
The Pentek Jade Architecture is based on the Xilinx Kintex UltraScale FPGA, which raises the digital signal processing (DSP) performance by over 50% with equally impressive reductions in cost, power dissipation and weight. As the central feature of the Jade Architecture, the FPGA has access to all data and control paths, enabling factory-installed functions including data multiplexing, channel selection, data packing, gating, triggering and memory control. A 5 GB bank of DDR4 SDRAM is available to the FPGA for custom applications. The x8 PCIe Gen 3 link can sustain 6.4 GHz data transfers to system memory. Eight additional gigabit serial lanes and LVDS general purpose I/O lines are available for custom solutions.
Pentek's Navigator" Design Suite was developed from the ground up to work with Pentek's Jade architecture and Xilinx's Vivado Design Suite® providing an unparalleled plug-and-play solution to the complex task of IP and control software creation and compatibility. The Navigator Design Suite consists of two components: Navigator FDK (FPGA Design Kit) for integrating custom IP into Pentek sourced designs and Navigator BSP (Board Support Package) for creating host applications. Users can work efficiently at the API level for software development and with an intuitive graphical interface for IP design. The Navigator BSP is available for Windows and Linux operating systems.
With a Pentek 8266 SPARK® PC, 8264 SPARK 6U VPX, or 8267 SPARK 3U VPX development system, work can begin immediately on applications. A SPARK system saves engineers time and expense associated with building and testing a development system and ensures optimum performance of Pentek boards. SPARK development systems are ready for immediate operation with software and hardware installed. In many applications, the SPARK development system can become the final deployed application platform.
The Model 71141 XMC module is designed to operate with a wide range of carrier boards in PCIe, 3U and 6U VPX, AMC, and 3U and 6U CompactPCI form factors, with versions for both commercial and rugged environments.
For the latest pricing, delivery and available options, please fill out this form and your request will be delivered to the appropriate department. To learn more about our products or to discuss your specific application please email our sales department at firstname.lastname@example.org, contact your local representative or Pentek directly:
One Park Way
Upper Saddle River, NJ 07458
Tel: +1 (201) 818-5900
Fax: +1 (201) 818-5904
Map + Directions
|CONNECT ON SOCIAL:|